Nutrition in the Substrate: Vermicompost and Slow-Release Fertilizers

Approximate pH: vermicompost more often has a pH of 6.5–8.5, but the exact value depends on the raw material and the maturity of the product. For slow-release fertilizers, the pH of the granule itself is not the main parameter: what matters more is the composition, the dose, the coating, and the product's effect on the pH of the finished substrate.

Substrate components are responsible for water, air, and support for the roots, but they do not always supply the plant with available nutrients. In soilless mixes the reserve of elements is usually limited, so nutrition is planned separately: it can be applied with watering or partly built into the substrate.

Nutrients added in advance create a reserve of elements and make the plant less dependent on each individual feeding. At the same time, the amount must match the pot volume, the growth rate, the composition of the mix, and the feedings that follow.

Two ways to build in nutrients

In home substrates the following are used most often:

These materials work differently.

Vermicompost contains organic matter and elements that are released as it dissolves and mineralizes. Its composition can vary greatly.

Slow-release granules contain a calculated reserve of mineral salts. Their coating regulates how fast the nutrient solution comes out.

Vermicompost

Vermicompost is produced when organic raw material is processed by earthworms and microorganisms. It is often sold as "worm castings" or "biohumus."

It can add to a mix:

The composition depends on the raw material, maturity, and production technology. The name "vermicompost" by itself does not tell you the exact concentration of elements, the pH, or the EC.

Vermicompost is not a structural base. A large amount of fine material can compact the mix, increase its water-holding capacity, and raise the salt concentration.

How much vermicompost to add

Approximate share:

When using vermicompost, keep in mind that it is already a source of nutrients. Additional liquid feeding after repotting is not started right away and is given at a lower concentration.

A good-quality mature product has a uniform crumbly structure and smells of earth. Material with an ammonia, rotten, or sharply sour smell is not added to a potting mix.

Controlled-release fertilizers

Slow-release granules consist of a core with soluble nutrient salts and a protective coating.

The core may contain nitrogen, phosphorus, potassium, magnesium, and micronutrients. The exact composition depends on the formula of the particular product and is given on the package.

The coating is made of polymers, resins, wax, sulfur, or combinations of them. In products like Osmocote, the soluble fertilizer is enclosed in a coating through which water gradually penetrates.

How a granule releases its contents

After moistening, water passes through the coating and dissolves the salts inside the granule. Moisture starts the process, and the temperature of the root environment affects how fast the nutrient solution is released.

In a warm, constantly moist substrate the granules work more actively. In summer, especially on a warm windowsill or next to a heater, the fertilizer may finish working earlier than the stated period. With an excessive dose, this raises the risk of too high a salt concentration and root burn.

That is why slow-release fertilizers are not added "with a margin." The dose is calculated according to the instructions of the particular product, the volume of substrate, the temperature, and the needs of the plant.

A damaged coating can release its concentrated contents faster. Granules are not crushed and not placed right up against the roots.

After the nutrients have come out, the coating stays in the substrate for some time and can look like a working granule. You cannot tell from its appearance whether any fertilizer is left inside.

How to choose a formula

A fertilizer formula is chosen not only by the brand name but also by the ratio of elements and the growth stage.

For foliage plants, balanced formulas with enough nitrogen, which is needed to form leaves and shoots, are more often chosen.

For flowering plants, formulas designed for the budding and flowering period are used. They may have a different ratio of nitrogen, phosphorus, and potassium, but you should go by the composition of the particular product, not just the word Bloom on the package.

A fertilizer for flowering plants does not necessarily suit foliage plants, and a formula for active growth may be excessive during rest or flowering.

Before applying, check:

Why build in nutrients in advance

In soilless mixes, soluble elements are partly washed out with watering. Nutrients added in advance can:

At the same time, granules do not make care fully automatic. The plant still depends on light, temperature, water, the condition of its roots, and the pH of the medium.

When it is better not to build in nutrients

Nutrients added in advance are skipped or used at a minimal dose:

First the plant must restore its roots and start growing actively. Only after that is feeding gradually increased.

How to choose the overall scheme

Vermicompost is chosen when a moderate organic additive is needed and the mix can tolerate more fine moisture-retentive material.

A slow-release fertilizer is chosen when a known composition, a calculated dose, and a predictable duration matter.

A pre-fertilized bagged soil, vermicompost, slow-release granules, and a full dose of liquid fertilizer are not automatically stacked together. All sources of nutrients are considered together so as not to raise the EC of the root environment above a safe level.

The main rule

Nutrition in the substrate should be a calculated part of the care system, not an extra layer "just in case." When choosing, consider not only the composition of the additive but also the size of the pot, the water-holding capacity of the mix, the temperature, the lighting, the water quality, and the feedings that follow.