Charcoal
Approximate pH: most often neutral or alkaline, roughly 6.5–10.0. Charcoal has no single pH: the reaction depends on the type of wood, the firing temperature, the amount of ash, the particle size, and rinsing.
Charcoal is made by heating wood with limited access to oxygen. In this process most of the volatile compounds are driven out of the wood, while the porous carbon framework remains.
For plants, pure charcoal or specially prepared biochar is used. It is not the same as activated charcoal from tablets or filters.
What charcoal gives a substrate
Porous charcoal particles:
- add a structural fraction;
- hold some water;
- adsorb certain dissolved compounds;
- can hold some nutrient ions;
- support a microenvironment for microorganisms;
- reduce the density of the mix when the particle size is suitable.
The effect depends on the surface area, pore size, raw material, and production temperature. Charcoal from different batches can behave completely differently.
Charcoal is not a complete fertilizer. Wood charcoal usually contains little available nitrogen, and its ash and mineral content can vary greatly.
Charcoal and biochar
In everyday use, the words "charcoal" and "biochar" are often used as synonyms, but their purpose can differ.
Charcoal is usually produced as fuel. It may still contain ash, dust, and foreign impurities.
Biochar is produced specifically for use in soil or substrate. The manufacturer may state the raw material, pyrolysis temperature, pH, EC, and ash content.
The higher the pyrolysis temperature, the higher the carbon stability, porosity, and pH of the material usually are. However, the properties are determined by the whole production technology.
How much to add
Approximate share of charcoal:
- 3–5 % — a small functional additive;
- 5–10 % — the usual cautious range;
- up to 15 % — only after checking the pH, EC, and behavior of the mix.
There is no universal scientific standard for all houseplants. The share is chosen according to particle size, the composition of the base, and the response of the particular plant.
A large amount of charcoal can:
- raise the pH;
- change the availability of micronutrients;
- hold some of the nutrients;
- increase the EC if it contains a lot of ash;
- make the mix too uneven;
- temporarily bind some of the nitrogen and other compounds.
Charcoal is added especially carefully to mixes based on acidic peat: an alkaline batch can noticeably change the reaction of the whole root environment.
Particle size
Large pieces work as a structural component and keep spaces open.
A medium fraction suits mixed substrates.
Fine crumbs increase the surface area and have a stronger effect on holding dissolved substances, but in excess they fill the spaces between large particles.
Dust is removed before use. It does not improve aeration and can make the mix denser.
Preparation
Before mixing, charcoal is:
- cleared of debris and ash;
- cleared of overly fine dust;
- rinsed until the water becomes noticeably clearer;
- sieved by size;
- soaked if needed;
- used moist or after drying.
Soaking helps push the air out of the pores and check whether the material colors the water with a lot of ash.
Some growers first keep charcoal in water or a weak nutrient solution. This can reduce the initial binding of some nutrients, but it does not replace checking the EC and is not a required procedure for every batch.
Charcoal that is not suitable
The following are not added to a substrate:
- charcoal with lighter fluid;
- scented briquettes;
- compressed briquettes with starch and binders;
- charcoal with impregnations;
- material with a petroleum or chemical smell;
- charcoal with a lot of unknown ash;
- charcoal from a campfire, if plastic, painted wood, or household waste may have burned in it.
Barbecue charcoal is suitable only if it is pure wood with no additives or fire accelerants.
Charcoal and root rot
Charcoal is not a fungicide, an antiseptic, or a cure for root rot.
It does not replace removing damaged roots, repotting into fresh substrate, correcting watering, ventilation, sufficient lighting, and treatment with a product when an infection is confirmed.
The porous surface can hold some organic compounds and odors, but that does not mean charcoal neutralizes any infection or toxin.
Charcoal and nutrition
The porous surface of charcoal can temporarily hold some nutrient ions. This can reduce their leaching, but at the same time it can lower the availability of elements right after application.
After adding a large amount of new charcoal, do not automatically raise the fertilizer dose. First watch the plant and check the EC if needed.
Charcoal can also hold some products and organic compounds. If the plant is receiving systemic plant protection products or special additives, charcoal in the substrate is taken into account as a possible sorbent component.
Which plants it suits
A small share of charcoal can be used in mixes for orchids and epiphytic aroids, in moisture-retentive organic substrates, in mixes with bark and coir chips, in terrariums, and for plants that need a loose, uneven structure.
Charcoal is not required for any group of plants. It is added only when its function in the particular mix is clear.
The main rule
Charcoal is a porous structural and sorbent additive with variable properties. Before use, assess its cleanliness, fraction, pH, EC, and effect on how the substrate dries. A small test batch is safer than adding a large amount of unknown charcoal to the whole collection at once.