Peat
Approximate pH: sphagnum (high-moor) peat usually has a pH of 3.5–5.0, transitional peat roughly 4.0–5.5, and low-moor (fen) peat more often 5.0–7.0. Exact values depend on the origin, degree of decomposition, and liming. The pH of a component and the pH of the finished mix are not the same thing.
Peat forms from plant remains under conditions of constant moisture and a lack of oxygen. In a substrate it works as a moisture-retentive organic base: it holds water, has a high cation exchange capacity, and helps retain dissolved nutrients.
Peat by itself is not complete nutrition. Its properties are determined by its type, degree of decomposition, grade, moisture, and preparation by the manufacturer.
Types of peat
High-moor peat forms mainly from sphagnum and other plants that get most of their water from precipitation. It is light, acidic, and usually contains a lot of fibrous particles.
Weakly decomposed high-moor peat keeps large pores and compacts more slowly. More decomposed material becomes fine and dense; it holds water more strongly, but after overwatering it contains less air.
Low-moor peat forms with the involvement of groundwater and surface water. It contains more mineral substances and is usually darker, denser, and less acidic. Its properties depend more on where it was extracted.
Which plants it suits
Acidic high-moor peat is chosen for plants that need an acidic or slightly acidic root environment. Such groups include many plants of the heath family and some ferns, but requirements differ between species: some ferns grow better in an acidic medium, others tolerate a neutral substrate.
For moisture-loving tropical plants, high-moor peat is used as the moisture-retentive part of a mix, but it is not chosen automatically just by the name of the plant. Light, temperature, pot size, and drying rate matter.
Transitional and low-moor peat are used when a denser and more nutrient-rich organic fraction with a less acidic reaction is needed. For most houseplants it is better to choose not "a type of peat in general" but a specific product with a known pH, grade, and set of additives.
Water and air
Peat can hold a large volume of water, but the amount of available air depends on the grade and compaction. Fine, broken-down material fills the spaces between particles after watering and stays saturated longer.
After severe drying, peat can become hydrophobic: water runs through cracks and down the walls of the pot without wetting the whole volume. Such a root ball is moistened gradually and evenly, not just with a quick surface watering.
How much to add
Approximate share of peat:
- 20–40 % — as the moisture-retentive part of a loose mix;
- 40–60 % — for moisture-loving plants with enough loosening material;
- up to 70–100 % — only under controlled conditions, for example for seedlings, rooting, or plants with a fine root system.
The larger the pot, the colder the room, and the less often the substrate dries, the less fine peat is used.
Preparation
Dry peat is moistened in small portions before mixing. Severely dried peat is first lightly sprayed or watered, mixed, and left until it is evenly saturated.
Before planting, peat is:
- loosened;
- cleared of large lumps and debris;
- checked for even moisture;
- checked for added lime and fertilizers;
- if needed, mixed with bark, perlite, pumice, or another structural material.
A ready-made bagged peat-based soil must not automatically be limed or fertilized again: the manufacturer may already have added these components.
Change over time
The organic structure gradually decomposes. The particles become finer, the substrate settles, and after watering it contains less air. The speed depends on the initial degree of decomposition, temperature, moisture, and how long the plant has been growing in it.
A settling surface does not in itself mean that new mix needs to be constantly added on top. First assess the roots and the structure of the whole root ball.
How to choose peat
Check:
- the type and degree of decomposition;
- the size and uniformity of the grade;
- the stated pH;
- whether liming additives are present;
- starter or slow-release fertilizer;
- whether it wets evenly;
- the amount of dust, twigs, and coarse inclusions.
Peat is matched to the roots, the pot, and the watering. A finer, uniform structure is acceptable for fine roots. Thick roots and large pots often need a more stable framework of bark or mineral components.