Acaricides, Insecticide-Acaricides, and Ovicides
Mites are arachnids, not insects. So an insecticide intended for aphids, whiteflies, or thrips does not necessarily work against spider mites, flat mites, or other plant-feeding mites.
For this group of pests, acaricides, insecticide-acaricides, and products with ovicidal action are used.
Acaricides
Acaricides are products intended for controlling mites.
They can act:
- on adults;
- on larvae;
- on nymphs;
- on eggs;
- on several stages at once.
The specific spectrum of action depends on the active ingredient and the label. You cannot assume that any acaricide automatically destroys eggs or all stages of the mite.
Insecticide-acaricides
Insecticide-acaricides can be used against both insects and mites, if both targets are listed on the label.
Such products can be useful:
- with a mixed infestation;
- when thrips and mites are on the plant at the same time;
- when the pest has not been fully confirmed;
- when one product is permitted for several groups of pests at once.
But the word "insecticide-acaricide" does not mean the product is equally effective against all insects and mites. Always check the particular target, stage, and application method.
Ovicidal action
Ovicidal action is a product's ability to kill eggs or disrupt their development.
It is especially important with spider mites, because eggs can survive a treatment with a product that works well on mobile individuals. A few days later larvae hatch from them, then nymphs, and the population recovers.
Ovicidal action can be:
- full — the product is stated to work against eggs;
- partial — the eggs are damaged only at some stages of development;
- indirect — the development of the female or the production of viable offspring is disrupted.
The exact wording is checked on the label. You cannot conclude that a product is ovicidal just because it belongs to the acaricides.
The mite life cycle and choosing a product
Most plant-feeding mites have an egg, a larva, two nymphal stages, and an adult. The larva usually has three pairs of legs, while the nymphs and adults have four.
| Stage | Features | What to consider when choosing |
|---|---|---|
| Egg | Often protected by a shell and can survive treatment | A product with stated ovicidal action or repeated monitoring after the larvae hatch is needed |
| Larva | Mobile, feeds less than the later stages | Check whether the product acts on young stages |
| Nymph | Feeds actively and goes through two instars | May be vulnerable to products that work on mobile individuals |
| Adult | Feeds, reproduces, and sustains the population | It is important to act on the females and not to repeat the same IRAC group back to back |
In spider mites the cycle can speed up in warm conditions. So you cannot leave arbitrarily long pauses between treatments.
Why one treatment is often not enough
One treatment may not cover the whole cycle if:
- the product acts only on mobile stages;
- the eggs have survived;
- the solution did not reach the undersides of the leaves;
- some of the mites were in webbing or hiding places;
- the plant was treated unevenly;
- new individuals came from neighboring plants;
- the interval was chosen without regard to temperature.
After the first treatment, assess not only the number of adult mites, but also whether new small individuals, fresh damage, and eggs appear.
An acaricide and an insecticide are not the same thing
The type of product is determined by the target group of organisms:
- insecticide — against insects;
- acaricide — against mites;
- insecticide-acaricide — against insects and mites, if the label says so;
- ovicide — a product, or a property of a product, aimed at eggs.
The word "sap-sucking" describes the way of feeding, not a taxonomic group. Both aphids and spider mites suck out the contents of plant cells, but they belong to different groups of organisms and require a different choice of products.
How to choose a product by stage
Before treatment, determine:
- Which mite is presumably present.
- Whether there are eggs, larvae, nymphs, and adults.
- Which side of the leaf and which hiding places they are in.
- Which stage the product acts on.
- Whether the product is permitted for the particular plant and room.
- Whether the treatment needs to be repeated.
- Which IRAC code is given for the active ingredient.
If a product works only on adults and nymphs, the scheme must take into account the later hatching of larvae from the eggs. If a product has ovicidal action, this is also checked on the label, not assumed from the name.
Combining products
Sometimes a scheme is built on the principle:
| A product for mobile stages | + | A product with ovicidal action |
|---|---|---|
| Acts on larvae, nymphs, and adult mites | Helps reduce the hatching of a new generation from the eggs |
This explains the logic of the scheme, but it is not permission to mix any two products. Before a tank mix, check compatibility, formulations, the risk of burns, and the label's instructions.
If compatibility has not been confirmed, the products are applied separately with an acceptable interval.
Rotating acaricides
Mites quickly acquire resistance when the same group is repeated. So different trade names are not considered a rotation until the active ingredients and IRAC codes have been checked.
When putting a course together, take into account:
- whether one mode of action is being repeated;
- whether different products belong to the same group;
- which stages each product affects;
- whether a repeat treatment is permitted;
- whether the product causes a mite outbreak by killing beneficial predators.
The detailed logic of rotation is covered in the article "Resistance and rotation".
Completeness of coverage
Contact acaricides require contact with the pest. When spraying, treat:
- the undersides of the leaves;
- the petioles;
- the leaf axils;
- the stems;
- areas with webbing;
- neighboring plants if they show signs of infestation.
Oil and soap products depend especially on even coverage. They do not protect untreated areas and may not penetrate dense webbing or an egg shell.
A practical procedure
- Isolate the plant.
- Confirm that the problem really is caused by mites.
- Check both sides of the leaves and whether there are eggs.
- Wash off dust and webbing, if this is compatible with the plant's condition.
- Choose an acaricide or insecticide-acaricide registered against the relevant mite.
- Check its action by stage and its IRAC group.
- Treat the plant with complete coverage.
- Repeat the inspection after the interval set by the label.
- If needed, change the mode of action, not just the trade name.
- Check the neighboring plants and the growing conditions.
The practical takeaway
An acaricide is intended for mites, an insecticide-acaricide for mites and insects, and ovicidal action has to do with killing eggs. These properties can be combined in one product, but they are not interchangeable.
With mites, you need to take the whole cycle into account: eggs, larvae, nymphs, and adults. A reliable scheme includes correct diagnosis, a product for the right stage, complete coverage, repeated monitoring, and rotation of modes of action.