Insecticides: Purpose and Choosing a Product

Insecticides are products for protecting plants from insect pests. They can act when applied to the plant, through the pest's digestive system, or after moving within the plant. The application method depends on the particular product and must be stated on its label.

An insecticide is not used on the general grounds that "something is wrong with the plant," but after the pest, its location, and its stage of development have been identified.

Which pests insecticides are used against

Insecticide treatment may be needed for infestations of:

Pest groupWhere they are usually foundWhat to consider
AphidsYoung leaves, shoots, budsMultiply quickly; colonies are often on tender tissue
ThripsUndersides of leaves, flowers, leaf axilsSome stages may be in the substrate or hiding places
WhitefliesUndersides of leavesAdults fly up when the plant is touched
MealybugsLeaf axils, petioles, growing point, stems, rootsThe waxy covering and hiding places make treatment harder
Armored and soft scalesLeaves, petioles, stemsAdults are protected by a scale cover or dense covering
Soil insectsSubstrate, rootsFoliar treatment may not reach most of the population

Mites are not insects. For spider mites, flat mites, and other plant-feeding mites, acaricides or products explicitly registered as insecticide-acaricides are needed. The word "insecticide" alone does not mean the product will work against mites.

Why the pest must be confirmed first

Similar damage can arise for different reasons. Spots, yellowing, leaf deformation, and stalled growth are sometimes caused not by insects, but by problems with the roots, lighting, watering, nutrition, or by diseases.

Before choosing a product, check:

  1. Whether the pests themselves or their traces are on the plant.
  2. Which parts of the plant they are on.
  3. Whether there are mobile young insects.
  4. Whether new leaves, flowers, or roots are being damaged.
  5. Whether there are similar symptoms on neighboring plants.
  6. Whether the changes are related to recent repotting, drying out, overwatering, or a burn.

If the pest has not been identified, treatment with a random product may give no result and make further diagnosis harder.

What to check when choosing

You cannot go by the trade name alone. Products with different names can have the same active ingredient or the same mode of action.

On the label and in the instructions, check:

A product's registration and permitted application methods depend on the country. A product suitable for agricultural crops is not necessarily permitted for ornamental houseplants.

Contact, stomach, and systemic action

Insecticides can differ in how they act.

Contact products act after landing on the pest's body. For them, even coverage and treatment of the undersides of the leaves, the leaf axils, and other places where insects hide are especially important.

Contact-stomach products act on direct contact and after the pest eats treated tissue.

Systemic products move within the plant. The pest receives the active ingredient by feeding on the sap. This route can be useful against insects that feed in hidden places, but it does not mean that eggs or all stages will automatically be destroyed.

A detailed explanation of modes of action is given in the article "How products work".

The pest's stage matters

The same product can act differently on eggs, larvae, nymphs, and adults. Some products affect only certain stages, so part of the population may survive after the first treatment.

The following are especially hard to control:

So a scheme is chosen with the pest's full life cycle in mind. Intervals between treatments are determined by the label, the temperature, and the results of repeat inspections.

An insecticide does not replace mechanical cleaning

With mealybugs and armored and soft scales, the accessible colonies are first removed with a cotton swab, a soft brush, or another safe method. This reduces the number of pests and improves the product's contact with the remaining insects.

Mechanical cleaning is especially important if:

After cleaning, the plant is inspected again: eggs, young nymphs, and individual insects in hiding places may remain nearby.

Why there is no universal insecticide

A product that works well on aphids may turn out to be not effective enough against scale or thrips. The reasons can vary:

So choosing the "strongest" product does not replace correct diagnosis and a consistent scheme.

Common mistakes

Treating without confirming the pest

If the cause of the damage has not been established, an insecticide may be useless. First you need to find signs of insects and distinguish them from symptoms of diseases or care problems.

Using an acaricide against insects

An acaricide is intended for mites. It does not replace an insecticide for infestations of aphids, thrips, whiteflies, or mealybugs.

Repeating one product without regard to the mode of action

Different trade names do not always mean different modes of action. To reduce the risk of resistance, rotation is done by active ingredient and IRAC group, not by the name on the package.

Treating only the upper side of the leaves

Pests are often under the leaf, in the leaf axils, on the petioles, the stems, or in the growing point. Incomplete coverage leaves part of the population alive.

Increasing the dose

A higher concentration does not guarantee a better result. It can cause burns, toxicity to the plant, and increased danger to people. Use only the dose and application method from the current label.

A practical procedure

  1. Isolate the infested plant.
  2. Identify the pest and where it is located.
  3. Remove accessible colonies mechanically, if it is safe.
  4. Choose a product registered against this pest and suitable for the particular plant.
  5. Check the active ingredient, the mode of action, and the application method.
  6. Treat all parts of the plant that the product needs to reach.
  7. Keep to the repeat-treatment interval on the label.
  8. Inspect the plant and the neighboring collection again.
  9. If the pest persists, check the hiding places, the completeness of coverage, the stage of development, and the risk of resistance.

The practical takeaway

Insecticides are used against insects, but not against every pest indiscriminately. The right choice is based on a confirmed diagnosis, where the pest is, its stage of development, the active ingredient, and the permitted application method.

For a lasting result, insecticide treatment is combined with isolation, mechanical removal, repeated monitoring, and rotation of modes of action. The system is chosen according to the label of the particular product and the plant's growing conditions.

- Acaricides and insecticide-acaricides